Attaching martingale to girth
 
 

       The Horse Forum > Horse Tack > Horse Tack and Equipment

Attaching martingale to girth

This is a discussion on Attaching martingale to girth within the Horse Tack and Equipment forums, part of the Horse Tack category
  • Martingale to girth attachment
  • Attaching martingales

 
LinkBack Thread Tools
    05-26-2010, 03:56 PM
  #1
Foal
Attaching martingale to girth

I've got a neophyte question: I've got a girth that has a D-ring and a standing martingale that does not have a clip. Can you get clips for standing martingales to attach to the girth's D-ring, or do you have to buy special martingales for this? I can't figure out how to undo the buckle on the martingale to get a clip on it. Normally, we've been just slipping the girth through the loop in the martingale, but we've got a girth that's too wide to do that.
     
Sponsored Links
Advertisement
 
    05-26-2010, 10:03 PM
  #2
Green Broke
You could always tie something around the loop on the martingale and leave it on and clip it to the girth when you put it back, or on the breastcollar if you use one. That's what some of our horses use, most of them do have a double clip to attach to the d-ring on the girth though. I don't think they're really expensive either, so it shouldn't be too much of an issue (depending, no offense) to go out and buy one with a double clip so you can just clip it on if you would rather that than tying it and leaving it attached..
This is just what we do at my barn, so it might not be the best thing, but works **** near fine, never had one break or untie itself. :3
Posted via Mobile Device
     
    05-26-2010, 10:24 PM
  #3
Foal
Thanks. I may end up doing that. It just seems like there should be a way to put a clip on the martingale that would be acceptable for a show where you have to take the martingale on or off depending upon what type of class it is.
     
    05-26-2010, 11:01 PM
  #4
Green Broke
You could probably buy just a double clip and attach it to the loop onthe martingale, and onto the girth, along with being able to unclip the clip attached to the girth, and his/ her bridle or headstall. :3
Posted via Mobile Device
     
    05-27-2010, 09:09 AM
  #5
Foal
I'll check into that.
     
    05-27-2010, 12:44 PM
  #6
Showing
If the leather is thin enough, just loop it through the bottom of one of these:

Then you can use the clip to attach to the d-ring
     
    05-27-2010, 04:25 PM
  #7
Foal
That's kind of what I was thinking of doing, but you can't undo the buckle on the Martingale to loop it through it.

Quote:
Originally Posted by JustDressageIt    
If the leather is thin enough, just loop it through the bottom of one of these:

Then you can use the clip to attach to the d-ring
     

Thread Tools

Similar Threads
Thread Thread Starter Forum Replies Last Post
INO: Western girth, buy or trade for english girth ExquisiteEquines Tack and Equipment Classifieds 1 05-02-2010 09:00 PM
Attaching Crupper with Block. HorsesAreForever Horse Training 15 01-30-2010 10:43 AM
Martingale--am i doing this right? equiniphile Horse Tack and Equipment 17 08-17-2009 11:54 AM
Attaching and Fitting Western Breast Collars Velvetgrace Horse Tack and Equipment 4 05-23-2009 06:19 PM



All times are GMT -4. The time now is 04:09 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0